Kenmore dryer repair
Kenmore Dryer Repair in Arlington, VA
Your Kenmore dryer is diagnosed in place at your Arlington address. You learn which part failed and what the fix costs before anything is repaired.
Booking online? Include the kenmore dryer model number and your Arlington address so parts can be checked ahead of the visit.
Step one covers the appliance; step two, your contact details. We follow up to book the visit.
dryer brands we service
Kenmore Dryer Repair for Owners, Renters and Landlords
This page covers ZIPs 22201 and 22203. Kenmore has no connection to us, and an appliance still inside the Kenmore warranty period belongs with the manufacturer first. After that, send us the model number with your booking so parts can be checked ahead of the visit.
How a Dryer Repair Visit Works
Tell Us What's Wrong
Name the make, add the model number if it is handy, and describe the symptom. A picture of the label inside the door lets us check parts.
Diagnosis at Your Home
The technician tests the appliance along with its power, water, drain, gas or vent connections until the fault is confirmed.
A Price Before Work
We name the failed part and give you the cost of fixing it. Work starts only after you agree.
Repair and Check
The part is installed and the appliance is run through a cycle so you can watch it working.
Related Repairs
Other appliances, brands and service areas on the site.
Kenmore Dryer Symptoms
One symptom can have several causes, so the technician tests the likely parts on site and quotes only once the culprit is confirmed.
- Not Heating
- Drum Not Tumbling
- Takes Too Long to Dry
- Making Loud Noise
- Won't Start
- Dryer Overheating
- Not Drying Clothes
- Shutting Off Early
- Not Getting Hot Enough
- Taking Too Long to Dry
- Thermal Fuse Blown
- Heating Element Burned Out
- Gas Igniter Not Working
- Gas Valve Solenoid Failure
- Flame Sensor / Radiant Sensor Failure
- Blower Wheel Clogged with Lint
- Exhaust Duct Clogged
- Restricted Exhaust Airflow
- Dryer Venting Improperly
- Drive Belt Broken
- Drum Rollers Worn Out
- Drum Glide / Bearing Worn
- Idler Pulley Seized
- Drive Motor Failure
- Making Loud Noise During Operation
- Squealing Noise During Tumble
- Thumping or Banging Noise
- Rattling Noise
- Control Board Failure
- Cycling Thermostat Failure
- High-Limit Thermostat Failure
- Moisture Sensor Failure
- Dryer Door Not Closing Properly
- Door Switch Failure
- Lint Trap / Screen Damaged
- Start Button Not Working
- Dryer Won't Turn On
- Tripping Circuit Breaker
- Burning Smell
- Clothes Shrinking
- Clothes Still Wet After Full Cycle
- Clothes Damp but Warm After Cycle
- Auto-Dry Sensor Not Working
- Timer Not Advancing
- Electric Dryer No Heat — Partial Power
- Gas Smell from Gas Dryer
- Display Panel Not Working
- Buttons Not Responding
- Won't Spin at All
- Stops Mid-Cycle
- Heat Setting Not Changing
- Excessive Energy Use
- Excessive Static on Clothes
- Clothes Heavily Wrinkled
- Steam Function Not Working
- Moisture Sensor Needs Cleaning
- Exhaust Hose Kinked
- Exterior Too Hot to Touch
- Wrinkle-Prevent Tumble Not Working
- Requires Two or More Cycles to Dry
- Error Code on Display
- Low Gas Pressure to Dryer
- Drum Interior Light Not Working
- Door Handle Broken
- Auto-Dry Cycle Runs All Night
- Gas Burner Orifice Clogged
- Lint Fire Hazard in Ductwork
- Timer Advancing Too Slowly
- Three-Prong Outlet / Four-Prong Cord Mismatch
- Knocking at Startup
- Intermittent Squeaking
- Bird or Pest Nest in Dryer Duct
- Cycling Thermostat Stuck Closed
- Gas Valve Solenoid Kit Needed
- Thermal Cutout Needs Resetting
Other Dryer Brands
Kenmore Appliances We Service
Kenmore Dryer Notes
Kenmore dryer repair across all 2 Arlington ZIP codes we cover. We find the fault at your home and give you a price to approve before anything is done.
In this part of Arlington, a repair often begins at a front desk. Between Court House and Ballston a great many people live in towers where the washer and dryer are stacked in a closet, the refrigerator is framed in by cabinets, and the route to the kitchen runs through a garage, a lobby and an elevator. The other half of the work is a short walk away, in houses built between the wars, where the concern is more likely a basement drain older than anyone living upstairs.
On a Kenmore dryer, the checks run in this order: the exhaust path out of the house before anything electrical, meaning the outside hood, the duct, the transition hose behind the machine and the lint route, ahead of the element, the thermal fuse or the gas igniter, since a restricted vent is usually what took out the last part. Worth knowing as well: two Kenmores that look alike on the outside may share nothing inside, so no part can be picked from the badge alone.
Call or book online, and we'll agree on a time together.
How a Kenmore dryer is put together
Kenmore dryers are mostly Whirlpool (110) or LG (796) designs, in gas and electric. On a Whirlpool-built electric that tumbles without heat, we meter the one-time fuse first, then the coil element and its limit thermostat; on a gas model, a glowing igniter that never lights the burner points to the valve coils. A dryer that won't start at all often has a blown thermal fuse or a failed door switch. Squealing, thumping or a scraping drum means rollers, the idler pulley or drum glides. LG-built models have their own sensor and board logic and often show a code. Behind almost every heating failure is airflow, so we look at the vent run, especially the long ducts that snake through basement ceilings in older houses.
Also: once the real builder is known, a Kenmore gets the same tests and the same parts as that company's own models.
Where Kenmore dryers tend to fail
The first things we check on this model line: Thermal fuse blown; Heating element open; Gas valve coils failing; Drum rollers or idler squealing; Restricted exhaust vent.
Those are starting points, not a verdict. One symptom can trace to a cheap part or an expensive one, so the cause is confirmed at your home before you're quoted.
Where the dryer sits in Arlington
In Arlington's condo towers a dryer either feeds a building duct or has no outside vent at all. If drying drags on, look at the building duct or a ventless model's filters before the heater.
A stacked dryer in a Arlington closet needs air to breathe; a louvered door, or leaving the door open while it runs, often shortens drying times.
The dryer symptom that fools people
Whatever the brand, the dryer complaint most often misread is a dryer that has had its thermal fuse or heating element replaced more than once while the blocked vent that caused the first failure is still in the wall.
The local factor to keep in mind in Arlington, where most homes are high-rise condos and garden apartments: vent runs that cross a finished lower level or climb through a second floor to the roof, stacked dryers exhausting into building ducts, and heavy, damp lint in humid weather.
Gas ranges, dryers and safety
Glowing oven igniters with no flame, clicking burners that never light and gas dryers that spin without heat are everyday gas repairs. The usual parts are a weak igniter, a valve coil or a flame sensor.
The piping and the shutoff valve upstream of the appliance belong to a gas fitter; if we spot trouble there, you'll hear about it.
In Brief
Kenmore Dryer Questions
Brief answers to what customers most often ask us. Don't see yours? Ask when you call, or add it to the notes when you book online.
Still have a question?
Get in touch with the brand, the symptom and, if you can find it, the model number. Some things we can answer right away; others need a technician in front of the machine.
The brand, the model number and a sentence about what's wrong, plus any error code exactly as it appears. A photo of the rating label is even better; it's the surest way to arrive in Arlington with the right parts the first time.
Yes, and plainly. When a fix would eat much of the price of a comparable new model and the unit is late in its life, we'll suggest you replace it rather than repair it, in Arlington or anywhere. Built-ins get more latitude, since a new one usually means new cabinetry too.
We can't say until we know what failed. A valve, switch, pump or element costs far less than a control board or sealed-system work, and you get the actual figure after diagnosis, before any repair.
It's more likely if you send the model number when you book. The Kenmore name has been on machines from more than one manufacturer, so parts are ordered by the model number, never by the badge. If a part has to be ordered, you hear the lead time before you decide.