Roper dryer repair
Roper Dryer Repair in Arlington, VA
Your Roper dryer is diagnosed in place at your Arlington address. You learn which part failed and what the fix costs before anything is repaired.
Booking online? Include the roper dryer model number and your Arlington address so parts can be checked ahead of the visit.
Step one covers the appliance; step two, your contact details. We follow up to book the visit.
dryer brands we service
Roper Dryer Repair for Owners, Renters and Landlords
This page covers ZIPs 22201 and 22203. Roper has no connection to us, and an appliance still inside the Roper warranty period belongs with the manufacturer first. After that, send us the model number with your booking so parts can be checked ahead of the visit.
How a Dryer Repair Visit Works
Tell Us What's Wrong
Name the make, add the model number if it is handy, and describe the symptom. A picture of the label inside the door lets us check parts.
Diagnosis at Your Home
The technician tests the appliance along with its power, water, drain, gas or vent connections until the fault is confirmed.
A Price Before Work
We name the failed part and give you the cost of fixing it. Work starts only after you agree.
Repair and Check
The part is installed and the appliance is run through a cycle so you can watch it working.
Related Repairs
Other appliances, brands and service areas on the site.
Roper Dryer Symptoms
One symptom can have several causes, so the technician tests the likely parts on site and quotes only once the culprit is confirmed.
- Not Heating
- Drum Not Tumbling
- Takes Too Long to Dry
- Making Loud Noise
- Won't Start
- Dryer Overheating
- Not Drying Clothes
- Shutting Off Early
- Not Getting Hot Enough
- Taking Too Long to Dry
- Thermal Fuse Blown
- Heating Element Burned Out
- Gas Igniter Not Working
- Gas Valve Solenoid Failure
- Flame Sensor / Radiant Sensor Failure
- Blower Wheel Clogged with Lint
- Exhaust Duct Clogged
- Restricted Exhaust Airflow
- Dryer Venting Improperly
- Drive Belt Broken
- Drum Rollers Worn Out
- Drum Glide / Bearing Worn
- Idler Pulley Seized
- Drive Motor Failure
- Making Loud Noise During Operation
- Squealing Noise During Tumble
- Thumping or Banging Noise
- Rattling Noise
- Control Board Failure
- Cycling Thermostat Failure
- High-Limit Thermostat Failure
- Moisture Sensor Failure
- Dryer Door Not Closing Properly
- Door Switch Failure
- Lint Trap / Screen Damaged
- Start Button Not Working
- Dryer Won't Turn On
- Tripping Circuit Breaker
- Burning Smell
- Clothes Shrinking
- Clothes Still Wet After Full Cycle
- Clothes Damp but Warm After Cycle
- Auto-Dry Sensor Not Working
- Timer Not Advancing
- Electric Dryer No Heat — Partial Power
- Gas Smell from Gas Dryer
- Display Panel Not Working
- Buttons Not Responding
- Won't Spin at All
- Stops Mid-Cycle
- Heat Setting Not Changing
- Excessive Energy Use
- Excessive Static on Clothes
- Clothes Heavily Wrinkled
- Steam Function Not Working
- Moisture Sensor Needs Cleaning
- Exhaust Hose Kinked
- Exterior Too Hot to Touch
- Wrinkle-Prevent Tumble Not Working
- Requires Two or More Cycles to Dry
- Error Code on Display
- Low Gas Pressure to Dryer
- Drum Interior Light Not Working
- Door Handle Broken
- Auto-Dry Cycle Runs All Night
- Gas Burner Orifice Clogged
- Lint Fire Hazard in Ductwork
- Timer Advancing Too Slowly
- Three-Prong Outlet / Four-Prong Cord Mismatch
- Knocking at Startup
- Intermittent Squeaking
- Bird or Pest Nest in Dryer Duct
- Cycling Thermostat Stuck Closed
- Gas Valve Solenoid Kit Needed
- Thermal Cutout Needs Resetting
Other Dryer Brands
Roper Appliances We Service
Roper Dryer Notes
Roper dryer repair across all 2 Arlington ZIP codes we cover. We find the fault at your home and give you a price to approve before anything is done.
In this part of Arlington, a repair often begins at a front desk. Between Court House and Ballston a great many people live in towers where the washer and dryer are stacked in a closet, the refrigerator is framed in by cabinets, and the route to the kitchen runs through a garage, a lobby and an elevator. The other half of the work is a short walk away, in houses built between the wars, where the concern is more likely a basement drain older than anyone living upstairs.
On a Roper dryer, the checks run in this order: the exhaust path out of the house before anything electrical, meaning the outside hood, the duct, the transition hose behind the machine and the lint route, ahead of the element, the thermal fuse or the gas igniter, since a restricted vent is usually what took out the last part. Worth knowing as well: Whirlpool parts fit a Roper, so even an older machine is easy to supply.
Call or book online, and we'll agree on a time together.
How a Roper dryer is put together
A Roper dryer is essentially a basic Whirlpool 29-inch dryer, and those have well-known failure points. A thermal fuse on the blower housing opens when airflow is poor, stopping the dryer or its heat depending on the model. Electric versions add a thermal cutoff and a high-limit thermostat near the element. Gas versions use an igniter, a flame sensor and valve coils. The drum rides on rear rollers and is driven by a belt kept tight by an idler pulley, and all three wear out. We check the vent from the dryer to the outside hood, test the fuses and heat source, and inspect the drive parts by hand.
Also: most Roper failures turn out to be simple: a lid switch, a drain pump, a drive belt or a thermal fuse.
Where Roper dryers tend to fail
The first things we check on this model line: Thermal fuse on the blower housing blown; Thermal cutoff open on electric model; Gas igniter cracked; Rear drum roller worn; Idler pulley squealing.
Those are starting points, not a verdict. One symptom can trace to a cheap part or an expensive one, so the cause is confirmed at your home before you're quoted.
Where the dryer sits in Arlington
In Arlington's condo towers a dryer either feeds a building duct or has no outside vent at all. If drying drags on, look at the building duct or a ventless model's filters before the heater.
A stacked dryer in a Arlington closet needs air to breathe; a louvered door, or leaving the door open while it runs, often shortens drying times.
The dryer symptom that fools people
Whatever the brand, the dryer complaint most often misread is a dryer that has had its thermal fuse or heating element replaced more than once while the blocked vent that caused the first failure is still in the wall.
The local factor to keep in mind in Arlington, where most homes are high-rise condos and garden apartments: vent runs that cross a finished lower level or climb through a second floor to the roof, stacked dryers exhausting into building ducts, and heavy, damp lint in humid weather.
After a power outage
Around Arlington, a July thunderstorm or a January ice storm can leave a street dark for a day or longer. Resist checking on the food: FoodSafety.gov's guidance is roughly four hours for a refrigerator kept shut, 48 for a packed freezer and 24 for one half full.
Electronics tend to suffer at the instant the power returns. An appliance that stays dead or flashes a code can often be reset by killing its breaker for a minute; if not, tell us about the outage when you call.
In Brief
Roper Dryer Questions
Brief answers to what customers most often ask us. Don't see yours? Ask when you call, or add it to the notes when you book online.
Still have a question?
Get in touch with the brand, the symptom and, if you can find it, the model number. Some things we can answer right away; others need a technician in front of the machine.
Usually, if we know ahead. Name each appliance that's misbehaving when you book the Arlington visit, model numbers included, and the day is planned with room for all of them.
A little. Most repairs are done where the machines stand, and around Arlington laundry is usually in a hall closet holding a stacked washer-dryer in the condo towers, a shared laundry room in the older garden-apartment buildings, and the basement of the detached houses. If the machines are upstairs, in a tight closet or behind a finished wall, mention it when you book so we can plan for anything that has to be moved.
We can't say until we know what failed. A valve, switch, pump or element costs far less than a control board or sealed-system work, and you get the actual figure after diagnosis, before any repair.
It's more likely if you send the model number when you book. Roper is built on the Whirlpool platform, and parts shared across that family are often still easy to find after a model is discontinued. If a part has to be ordered, you hear the lead time before you decide.